Vinyl Mastering?

Moderator: beatchemist

Vinyl Mastering?

Postby AS400XL on Sat Nov 13, 2010 3:38 pm

Posting this so I won't forget where it is
http://www.gearslutz.com/board/masterin ... lines.html

Namely http://www.gearslutz.com/board/914005-post6.html:
========

here are some important issues when vinyl cutting... (simple and ruff.. there is much more to the topic but I am in a hurry):

1)
cut off the infrasub below 15Hz.. tone arms resonate around 5-10Hz and the needle will jump when played back on turntables...

2)
check the phase alignment of everything below 500Hz .. should be very mono. how do you check? with a phase meter (keep it green) OR simply press MONO on your mixer / amp and listen if the bass is diminuished.. if so take out that cathedral reverb from the subsonics! ;-) .. kepp the stereo-wideners up of 500Hz!

3)
carefull with hihats around 8.4 KHz .. or "S"-tones in vocals... DE-ESS the shit out of it, really do... they will sound MUCH more aggressive on vinyl - you are going to regret it... the SHURE SM58 sounds like crap when recorded on vinyl.

for dance music I place a "safety" sharp butterworth 5 or 6 LO-PASS filter at around 18.5 or 19 KHz to avoid intermodulation of highs to lower frequencies (happens sometimes) ..

and the most important rule:

4)
keep it very, very slick and fat. weak mixes will sound terrible on vinyl.. good mixes will translate good even if the cutter is lazy or has a bad day.

5)
dont exagerate with loudness... that especially applies to vinyl. -12dB RMS is really hot enough.. the cutter should decide how hot he can print the whole plate...

6)
for 33 1/3 RPM (dance): keep the side under 15 mintes IN ANY CASE or it will sound like garbage. under 12 minutes will shine.

for 45 RPM (dance): keep the side under 9 minutes IN ANY CASE or it will sound worse then 33 1/3 (good 33 1/3 is superior to bad 45er cuts). for very loud an d crips records stay under 6 minutes for a 45er cut. these ones are my favourites..

7)
if you dont do much bass and you have a more "hifi-ish" recording try DMM (direct metal mastering) .. it sounds pretty close to heaven if done properly

just my few lazy answers...

I wish you phat tracks.

robert
======
User avatar
AS400XL
 
Posts: 13
Joined: Tue Feb 02, 2010 8:33 pm


Re: Vinyl Mastering?

Postby GhostTrolley on Sun Jun 05, 2011 12:26 pm

How do you know if you've done it right?

Big ups for the tips.
GhostTrolley
 
Posts: 5
Joined: Sun Jun 05, 2011 12:19 pm


Re: Vinyl Mastering?

Postby bekex on Thu Oct 11, 2018 5:25 am

Master of the foreign stint is regulated for the satisfaction of the candidates. The range of the deposing and top essay writing companies is fixed for the vital parts for the humans in life.
bekex
 
Posts: 1
Joined: Thu Oct 11, 2018 5:23 am


Re: Vinyl Mastering?

Postby lumuhuzum on Sat Nov 03, 2018 7:11 am

Frequency setting is often become problem for users of systems and use tools for setting of malfunctioning. With write of these words on here you make australian essay writing service reviews for handling of this problem in efficient way.
lumuhuzum
 
Posts: 1
Joined: Sat Nov 03, 2018 7:10 am



Return to Production Discussion

Who is online

Users browsing this forum: No registered users and 1 guest

cron